The transmission of the fan is verified by dynamic and static balance. The centrifugal opening system reduces the wind resistance and greatly improves the efficiency of the fan. When the fan is not running, the strong spring can close the shutter firmly. And the shroud is made of solid, coated steel plywood, and the shutters are made of coated sheet to ensure high strength. The middle hub and V-belt are made of die-cast aluminum and are equipped with strengthen the CZPT to increase the useful life.
Fan frame: zinc material, sheet thickness 1.0mm, zinc layer 275gm2
Fan blade: The fan blade is made of 1.5mm magnesium-plated aluminum-zinc plate. Passing the dynamic street test, it reduces energy consumption and extends service life.
Shutter: 275 gm high zinc layer sheet, 0.8mm thick, easy to install and remove
Belt: Imported from Japan Mitsuboshi or England PIX
Motor: Multiple motors to choose
We have more experience in producing and installing pig house fans. The fans can be configured according to the actual situation of the user to achieve a good ventilation effect.
SPEC OF FANS
QTY of blade
QTY of shutter
Diameter of blade
Air flow (0Pa) m³/h[cfm/W]]
Air Flow (-25Pa) m³/h[cfm/W]]
Air flow (-50Pa) m³/h[cfm/W]]
IEC motor protection class: IP55
Motor insulation grade: F
1.Shutter:With a centrifugal system which can ensure the shutter open and close automatically, and makes it dustproof, waterproof.
2.Motor: The high efficient and energy-saving moter with protection grade: Ip55, insulation class:F
3.Belt: Automatic tensioner to prevent the belt loosing and droping off.
4.Component:Centrifugal shutter system was made of 100% nylon, high intensity and long life.
1.Belt tensioner is made of aluminum magnesium alloy. It extend service life and avoid distortion.
2.Nylon orented poles are fixed on the flange which could avoid distorion of nylon and guarantee total concentrictiy of front and back bearings.
3.Handles are designed as recessed type,=. It is easy to carry, transport and have no effect on installation and outlook.
1. Quickly Response:24 hours on line services,with highest Quick Response Rate
2. Smooth Communication: Well-trained and experienced staffs to answer all your inquires.
3. Sincere Service Attitude: Customers first,be serious,be honest, be friendly.
4. OEM Accepted: Customized your products according to customer’s different requests.
Centrifugal push pull exhaust fan can be used in animal husbandry, greenhouse, factory, warehouse, workshop, large supermarket, swimming pool, the station waiting room and so on.
Low to medium levels of smoke and dust
Workshops where local exhaust ventilation is not possible.
To complement local exhaust ventilation systems.
Environments with changing sources of smoke and dust.
For large work pieces or where work positions are well separated.
Flexibly expandable by additional piping
Uninterrupted continuous operation due to automatic differential pressure-controlled filter cleaning
Little noise emission due to a particularly low noise level.
Heating costs minimised by air recirculation
Convenient operation due to intelligent control via touch screen with diagnostic system.
Contamination free dust collection due to compressed air lift for duct collection container.
Automatic filter cleaning, pressure-controlled
Control via touch screen
KemTex ePTFE filter cartridges
Dust collection container with pneumatic lifting device
Can be connected to various extraction systems
Can be combined with other intake systems to 1 extraction system
Can be extended
Low noise level
Types of V-Belts and Their Properties
A v-belt’s inside length and pitch are determined by measuring along the bottom side. The included angle of a v-belt is measured from its flanks when it is extended. Most v-belt sections are 40 degrees. There are different types of v-belts, and the dimensions of each are standardized by different organizations. This article will introduce the different types of v-belts and their properties.
Notched v-belts reduce bending stress
Notched V-belts reduce bending stress by reducing the axial length of the belt by 2 or more notches. These notches are characterized by different profiles, which differ in the pitch angle and the inside length. ISO and DIN standards are followed by the manufacturers of these belts. Notched v-belts are used on industrial machinery in countries other than the US.
Compared to the standard V-belts, notched ones are designed to resist bending stress better and offer better heat dissipation. They also last longer and run cooler than standard V-belts. Furthermore, they are about 2 percent more energy efficient than their standard counterparts. Therefore, notched V-belts are a viable replacement for standard V-belts.
Notched V-belts are commonly used in industrial applications because of their low price, ease of installation, and availability of many sizes. Another advantage of notched V-belts is that they provide more wedging force and higher load capacity. Notched V-belts have a wider v-groove than flat ones, which makes them more effective for heavy-duty applications.
Notched V-belts also provide better traction. They reduce bending stress, which is beneficial for preventing fatigue and tearing of v-belts. Additionally, v-belts can be installed in an existing equipment to add more performance. And with proper maintenance and installation, notched V-belts will provide trouble-free service for many years to come.
Ribbed v-belts reduce heat dissipation
Various kinds of v-belts are available for varying applications. The more popular types are the fractional horsepower and the double-V. Fractional horsepower v-belts are designed for light-duty applications, such as machine shop equipment and household appliances. The common sectional names are 2L, 3L, 4L, and 5L. The L in each of these belts refers to the top width of the belt, multiplied by 1 eighth inch.
Unlike conventional belts, ribbed v-belts are flexible, making them ideal for use in vibrating loads. They reduce heat dissipation and can be ordered in single or multiple sets to match your application. However, ribbed v-belts should not be mounted on deep-groove sheaves, as this can cause the belt to turn over. If you use deep-groove sheaves, the risk of rupture is very high. Deep-groove sheaves can also cut banded belts. Extremely worn sheaves can also cause the belt to rip.
The 2 types of ribbed v-belts differ in their construction and application. While both types have trapezium cross-sections, they are similar in that they are made of polyurethane or other durable materials. Ribbed v-belts have an additional layer of fabric on the elastomer core for reduced noise and better heat dissipation.
Ribbed v-belts are available in a variety of sizes, including trough v-belts. Their cross-sections are categorized by their top and bottom widths and depths. The included angle of most v-belt sections is approximately 40 degrees. Different types of v-belts have different cross-sections, and these cross-sections are standardized by various organizations.
As the load increases, a ribbed v-belt will wedge into the groove and decrease the amount of friction needed to maintain the correct torque. Flat belts can track off the pulleys due to friction. However, V-belts are more stable and require less width than flat belts. The main advantage of ribbed v-belts is their increased efficiency.
The global-local finite-element model is also used to calculate the maximum and minimum J-integrals during a belt’s running cycle. The data is then used to evaluate the durability of ribbed v-belts in various applications. The numerical models used for the calculations involve a ribbed V-belt with 5 full ribs.
Cogged v-belts increase lateral rigidity to reduce belt whip
Cogged v-belts are designed for maximum performance and durability on even the harshest drive systems. These belts are made from high-modulus polyester cords that resist hardening and stretch and provide superior balance and strength. They also feature raw-edge sidewalls to reduce slip and drive vibration. In addition, they have specially-formulated rubber compounds for oil resistance. CZPT Cog-Belt offers substantial savings in downtime, energy consumption and horsepower.
A double cogged v-belt combines the benefits of cogged and double vee-belts. Its bonded reinforced tie band offers enhanced flexibility and reduces belt whipping in multiple-belt drives. Double cogged v-belt dimensions vary depending on the standards of the manufacturer. Regardless of the type, you’ll want to use a belt that is aligned correctly.
Standard v-belts are also known as wrapped or raw edge v-belts. Wrapped V-belts feature fabric covers above and beneath the cord to increase lateral rigidity and reduce belt whip. Cogged V-belts also have fabric covers to prevent wear on the core and increase the belt’s operating temperature. They’re ideally suited for applications that require high-temperature operation.
Cogged V-belts can significantly decrease energy consumption and improve power transmission capabilities. They also have a bias-cut cover stock that provides axial and lateral stability while preserving the cord integrity. A fiber loaded cogged construction offers optimum flexibility while minimizing heat buildup. It can be installed on any type of drive, including chain conveyors and industrial-grade machines.
The two-layer tie-band permanently bonds multiple belts together. This provides maximum cord support, heavy shock absorption, and stability. The belts are also engineered with patented banding processes that eliminate belt turnover and distribute load evenly across the drive. CZPT Cog-Band Belts minimize belt whip and provide stability. They also minimize belt turnover and rollover in heavy-duty industrial applications.
A classic v-belt is the most common and economical belt. Its nominal dimensions are 1/2″ to 1-11/2″ wide and 16″ to 400 inches long. The width is usually 40 degrees. Different organizations use different cross-sections to classify v-belts. The following table provides a general comparison of the 2 types. The Cogged V-Belt is designed to reduce belt whip by increasing the lateral rigidity of the belt.
Cogged v-belts provide superior environmental resistance
The patented design of the Dayco V-Belt provides maximum power transmission while combining the benefits of a cogged belt and raw-edge construction. The belt’s top cogged design helps increase air flow around it, preventing deterioration and extending its useful life. The belt’s three-ply design features neoprene impregnated fabric for superior durability and a specially-formulated polyester cord for increased strength and stability.
A variety of v-belts are available, with cogged and notched versions presenting unique characteristics. Cogged V-belts are more flexible than uncogged versions and feature ‘X’-shaped grooves for enhanced heat dissipation. Cogged V-belts are interchangeable with conventional v-belts, although their ‘X’ design is most common. Hexagonal v-belts are a popular option for applications where traction is needed.
Another type of Cogged V-belt is designed specifically for outdoor power equipment. This v-belt is brown, with smooth clutching covers. Its aramid cord is very strong and provides superior durability in adverse conditions. Cogged V-belts can withstand severe shock loads and are therefore ideal for outdoor power equipment. Furthermore, they offer superior environmental resistance, minimal stretch, and a long service life.
A Cogged V-belt is composed of tensile cords that are supported by a rubber stock. Different manufacturers use different synthetic rubber stocks for this purpose. These materials help to extend the belt’s operating temperature range and resist premature failure. In addition to tensile cords, the belt’s body is covered with a fabric cover. The fabric is treated to form a chemical bond with the core materials, which allows it to withstand constant bending.